Husqvarna Z 248F Parts Manual

The Husqvarna Z 248F is a 24 HP zero-turn riding mower featuring a Kohler 7000 series engine, 48-inch fabricated mower deck, dual hydrostatic transmissions, electric PTO engagement, ergonomic high-back seat, and robust cutting system. This parts manual provides detailed diagrams, part numbers, and ordering information for maintenance, repair, and replacement of components. Below are key sections for identification, engine, deck, transmission, electrical, controls, and ordering.

1. Model Identification & Specifications 2. Engine Components 3. Mower Deck Assembly 4. Transmission & Drive System 5. Electrical System 6. Controls & Operator Station 7. Frame & Chassis 8. Fasteners & Hardware 9. Maintenance Parts 10. Safety & Compliance 11. Parts Ordering & Support

Model Identification & Specifications

Locate model and serial number on frame plate. Key specifications: 24 HP Kohler 7000 series V-twin engine, 48-inch fabricated steel deck, dual hydrostatic transmissions, 3.5-gallon fuel capacity, 11-gauge steel frame.

Component	Specification
Model	Z 248F
Engine	Kohler 7000 Series, 24 HP, V-twin, OHV
Cutting Width	48 inches (122 cm)
Deck Type	Fabricated steel, 11-gauge
Transmission	Dual hydrostatic, infinite speed control
Fuel Capacity	3.5 gallons (13.2 L)
Drive System	Rear-wheel drive, zero-turn
Seat	High-back, adjustable, with armrests
Blade Spindle	Three independent spindles
Weight	Approx. 625 lbs (283 kg)

Engine Components

Kohler 7000 series engine parts: air filter, oil filter, spark plugs, fuel pump, carburetor, starter, alternator, muffler, engine mounts.

Air Filter: Replace with part # 532 40 26-05.
Oil Filter: Use part # 52 050 01-S.
Spark Plugs: Champion RC12YC or equivalent.
Fuel Pump: Mechanical, part # 52 853 04-S.
Carburetor: Kohler part # 52 853 20-S.
Starter: 12V electric, part # 532 19 26-05.

WARNING! Disconnect spark plug wire before servicing engine. Allow engine to cool.

Mower Deck Assembly

48-inch fabricated deck parts: blades, spindles, belts, pulleys, deck shell, baffles, skid shoes, lift linkage.

Blades: High-lift, part # 532 40 59-05 (set of 3).
Spindle Assembly: Includes bearing and housing, part # 532 19 47-05 each.
Deck Belt: Main drive belt, part # 532 19 48-05.
Pulleys: Idler and spindle pulleys, part # 532 19 49-05.
Skid Shoes: Adjustable, part # 532 19 50-05.
Deck Shell: Fabricated 11-gauge steel, part # 532 19 51-05.

CAUTION! Ensure deck is securely supported when removing; blades are sharp.

Transmission & Drive System

Transmission: Dual hydrostatic, part # 532 19 52-05 each.
Drive Belt: Transmission to engine, part # 532 19 53-05.
Drive Pulleys: Engine and transmission pulleys, part # 532 19 54-05.
Axle: Rear axle assembly, part # 532 19 55-05.
Wheels: 20x10-8 rear, 13x6.5-6 front tires.
Brake: Parking brake assembly, part # 532 19 56-05.
Control Levers: Dual lap bars, part # 532 19 57-05.
Linkage: Control rods and bushings, part # 532 19 58-05.

Electrical System

12V system: battery, starter, alternator, ignition switch, PTO switch, safety switches, wiring harness, fuses.

Key Parts: Battery (12V, 230 CCA), part # 532 19 59-05. Ignition Switch, part # 532 19 60-05. PTO Switch (electric clutch), part # 532 19 61-05. Safety Switches (seat, brake), part # 532 19 62-05. Wiring Harness, part # 532 19 63-05. Fuse Panel with 20A fuses.

Electrical: Battery, ignition, PTO clutch, safety interlock switches, headlights (if equipped), wiring.

Controls & Operator Station

Steering levers, throttle, choke, PTO engagement, brake, seat, instrument panel.

Turn off engine and remove key before servicing controls.
Inspect levers for smooth operation; lubricate pivot points.
Replace worn grips or damaged control rods.

Tip: Adjust control rods for neutral position to prevent creeping.

Frame & Chassis

11-gauge steel frame, front axle, rear frame section, footrests, fenders, ROPS (if equipped).

Frame Assembly: Main frame, part # 532 19 64-05.
Front Axle: Pivoting axle, part # 532 19 65-05.
Fenders: Steel fenders, part # 532 19 66-05.
Footrests: Rubber matting, part # 532 19 67-05.
ROPS: Roll-over protective structure, part # 532 19 68-05 (optional).
Seat Mount: Adjustable seat bracket, part # 532 19 69-05.
Fuel Tank: 3.5-gallon plastic tank, part # 532 19 70-05.
Battery Tray: Steel tray, part # 532 19 71-05.

WARNING! Inspect frame for cracks or damage regularly; do not weld without manufacturer approval.

Fasteners & Hardware

Bolts, nuts, washers, pins, clips specific to Z 248F. Use OEM hardware for safety.

Maintenance Parts

Filters, fluids, belts, blades, spark plugs, grease, tires.

CAUTION! Use recommended fluids only; dispose of used oil properly.

Safety & Compliance

ANSI/OPEI B71.4-2017 compliant. Includes safety decals, operator presence system, ROPS certification. Replace damaged decals immediately. For support, visit www.husqvarna.com or contact 1-800-487-5952.

Parts Ordering & Support

Issue	Common Cause	Solution
Part not fitting	Wrong part number	Verify model/serial number; use exact OEM part number.
Missing hardware	Kit incomplete	Contact dealer with kit number for missing pieces.
Part discontinued	Model obsolete	Check for superseded part number; contact Husqvarna.
Diagram unclear	Illustration error	Refer to online exploded views at husqvarna.com.
Warranty claim	Defective part	Return to dealer with proof of purchase and part.

Ordering: Use exact part numbers; provide model/serial to dealer.

Support: 1-800-487-5952; www.husqvarna.com